|
||||||||||||||
|
G. Auslegung der grundlegenden Sicherheitsanforderungen zu Werkstoffen |
||||||||||||||
|
Leitlinie |
Akzeptiert |
Frage |
||||||||||||
| Leitlinie G-01 |
15.03.2016 | What is to be understood by harmonised standard as referred to in Annex I, section 4.2 b)? | ||||||||||||
| Leitlinie G-02 |
08.01.2016 | What is a ‘competent body’ for the certification of the quality (assurance) systems of material manufacturers? | ||||||||||||
| Leitlinie G-04 |
08.01.2016 | What are the ’suitable means’ for traceability referred to in Annex I Section 3.1.5 ? | ||||||||||||
| Leitlinie G-05 |
08.01.2016 | Annex I Section 4.3 of the PED requires that the equipment manufacturer must take appropriate measures to ensure that the material used conforms with the required specification. In particular, documentation prepared by the material manufacturer affirming compliance with a specification must be obtained for all materials. How may these requirements be applied in terms of required inspection documents? | ||||||||||||
| Leitlinie G-06 |
15.03.2016 | The 2nd paragraph of section 4.3 of Annex I gives requirements for the main pressure-bearing parts. How are they defined? | ||||||||||||
| Leitlinie G-07 |
15.03.2016 | To what apply the terms “having undergone a specific assessment for materials” of third paragraph of Section 4.3 of Annex I ? | ||||||||||||
| Leitlinie G-08 |
08.01.2016 | What are the certificates required for bolting parts? | ||||||||||||
| Leitlinie G-09 |
08.01.2016 | Can a material manufactured according to a standard or another publicly available specification for which a European Approval of Materials (EAM) is available, but for which the inspection document only refers to the standard or the specification on which the EAM has been based, be used for pressure equipment manufactured under the PED ? | ||||||||||||
| Leitlinie G-10 |
08.01.2016 | What are the requirements for the documentation and traceability of welding consumables: - Inspection document - Suitable procedures for traceability? |
||||||||||||
| Leitlinie G-11 |
15.03.2016 | Do the essential safety requirements of annex I apply to pressure equipment manufactured from plastic, GRP and other non metallic materials? | ||||||||||||
| Leitlinie G-12 |
15.03.2016 | Shall welding consumables and other joining materials comply with harmonised standards, European approvals of materials or particular material appraisal? | ||||||||||||
| Leitlinie G-13 |
15.03.2016 | What is meant by "Where appropriate", in the context of Annex I Section 4.1a when it refers to the quantitative values of Annex I Section 7.5? | ||||||||||||
| Leitlinie G-14 |
15.03.2016 | What does the exclusion of fine-grained steel in the first indent of Section 7.1.2 of Annex I of the directive mean? | ||||||||||||
| Leitlinie G-15 |
15.03.2016 | Annex I, section 4.2.b), first indent authorises the use of materials which comply with harmonized standards. Is this route still valid for a material for which the specification includes complementary requirements or improved properties to those of a grade in a harmonized EN material standard? | ||||||||||||
| Leitlinie G-16 |
08.01.2016 | The PED considers the case of a material manufacturer who "has an appropriate quality-assurance system, certified by a competent body established within the Union and having undergone a specific assessment for materials”. How should this requirement be understood in practice? | ||||||||||||
| Leitlinie G-17 |
08.01.2016 | What approach can be used to decide if a steel grade selected for a pressurized part requires specific impact properties? | ||||||||||||
| Leitlinie G-18 |
15.03.2016 | Do the essential safety requirements on materials specified in Annex I section 4.1 and section 7.5 apply to the base material or to the pressure equipment? | ||||||||||||
| Leitlinie G-19 |
08.01.2016 | Which requirements apply to components, such as dished ends, bolts, flanges, welded fittings etc, which are placed on the market as such? | ||||||||||||
| Leitlinie G-21 |
15.03.2016 | May a notified body perform a particular material appraisal (PMA) at the request of a material manufacturer? | ||||||||||||
| Leitlinie G-22 |
15.03.2016 | What is meant by the following two terms: "Other values" and "other criteria" in the context of Annex I Section 7.5? | ||||||||||||
| Leitlinie G-23 |
15.03.2016 | With which requirements of Annex I section 4 does the material used for a gasket have to comply? | ||||||||||||
| Leitlinie G-24 |
08.01.2016 | Annex I Section 4.3 of the Pressure Equipment Directive (PED) requires that the material manufacturer must prepare documentation affirming compliance with the specification required by the equipment manufacturer. Does this requirement mean that material properties used in the design of the pressure equipment must be based on those affirmed (guaranteed) by the material manufacturer? |
||||||||||||
| Leitlinie G-25 |
15.03.2016 | How shall welded tubes be considered for the application of the Pressure Equipment Directive (PED)? | ||||||||||||
| Leitlinie G-26 |
15.03.2016 | What type of material may follow the European Approval for Materials (EAM) route? | ||||||||||||
| Leitlinie G-27 |
15.03.2016 | When an equipment manufacturer receives a certificate type 3.1 according to EN 10204:2004 by the material manufacturer, in pursuance of the third paragraph of section 4.3 of Annex I, what evidence of compliance with these requirements shall be recorded in the technical documentation? | ||||||||||||
| Leitlinie G-28 |
15.03.2016 | How to apply Annex I, section 7.5 on the bending rupture energy measured on an ISO V test piece for base materials whose, due to its thickness, the collection of a test piece of section 10 mm x 10 mm is not possible? | ||||||||||||
| Leitlinie G-29 |
08.01.2016 | Based on data contained in a certificate issued by a material manufacturer (EN 10204:2004 3.1-certificate) material has been supplied in accordance with a material specification. May a pressure equipment manufacturer perform additional mechanical or non-destructive testing or have them performed to affirm that the material meets all the requirements specified by the equipment manufacturer? |
||||||||||||
| Leitlinie G-30 |
08.01.2016 | A manufacturer produces material only to a chemical analysis without mechanical testing and without affirmation of compliance to a material specification and/or grade. An entity intends to purchase the material and affirm compliance to a material specification by performing the mechanical tests as required by that material specification. There will be no further processing, other than cutting to size. Is this procedure acceptable and may this material be used in pressure equipment under the PED? |
||||||||||||
