|
||||||||||||||
F. Auslegung der grundlegenden Sicherheitsanforderungen zur Herstellung |
||||||||||||||
Leitlinie |
Akzeptiert |
Frage |
||||||||||||
Leitlinie F-01 |
08.01.2016 | According to section 3.1.2 (permanent joining) of Annex I, the third party must perform examinations and tests in order to carry out the approvals of operating procedures and personnel. Must the representative of the third party witness the whole permanent joining and testing process? | ||||||||||||
Leitlinie F-02 |
08.01.2016 | Which documents have to be available for the final inspection specified in Annex I Section 3.2.1? | ||||||||||||
Leitlinie F-03 |
15.03.2016 | How to interpret section 3.1.1 of Annex I as far as the forming procedures are concerned? Does it impose for the manufacturer a qualification procedure for forming operations which will be validated by the Notified Body? |
||||||||||||
Leitlinie F-04 |
15.03.2016 | Must a Notified Body take into account a procedure of permanent joints qualified by another Notified Body or a recognised third-party organisation? | ||||||||||||
Leitlinie F-05 |
15.03.2016 | Do the requirements related to permanent joints given in Annex I Sections 3.1.2 and 3.1.3 apply also to permanent joints other than welded joints? | ||||||||||||
Leitlinie F-06 |
15.03.2016 | In the absence of harmonized standards, what approach is to be followed for the approval of personnel carrying out permanent joining? | ||||||||||||
Leitlinie F-07 |
08.01.2016 | Does the concept of non-destructive testing as mentioned in Annex I Section 3.1.3 also cover visual examination? | ||||||||||||
Leitlinie F-08 |
15.03.2016 | What are ”the appropriate harmonized standards” in Annex I, section 3.1.2, last paragraph, which set out the examinations and tests for the approval of permanent joining procedures and personnel ? | ||||||||||||
Leitlinie F-09 |
15.03.2016 | Does the Pressure Equipment Directive require accreditation for the manufacturer’s testing laboratory that carries out non-destructive tests (NDT) or destructive tests (DT) of pressure equipment or of parts intended as pressure bearing parts of pressure equipment? | ||||||||||||
Leitlinie F-10 |
20.06.2016 | If a manufacturer has a procedure for permanent joining approved by a notified body or other recognized third-party organization at one site (location), may that manufacturer use the same procedure at other sites for similar applications? | ||||||||||||
Leitlinie F-11 |
15.03.2016 | In the absence of harmonized standards, what approach is to be followed for the approval of permanent joining procedures? | ||||||||||||
Leitlinie F-12 |
08.01.2016 | In the context of approval of welding procedures and personnel, what is meant by “the third party must perform examinations and tests as set out in the appropriate harmonized standards or equivalent examinations and tests”? | ||||||||||||
Leitlinie F-13 |
15.03.2016 | For pressure equipment in categories III and IV, can Non-Destructive Testing personnel holding qualifications other than those satisfying criteria of the harmonised standards (e.g. EN ISO 9712:2012 Non-destructive testing — Qualification and certification of NDT personnel) be approved by Recognised Third Party Organisations (RTPO) notified by a member state? | ||||||||||||
Leitlinie F-14 |
08.01.2016 | Does any welding operation on a pressure bearing component have to require a qualification of the welding procedures and of the welders/welding operators? | ||||||||||||
Leitlinie F-15 |
20.06.2016 | Where approval of operating procedures for permanent joining is required by the PED and the approval is granted on the basis of a document other than a harmonized standard, should this approval explicitly mention the PED? | ||||||||||||
Leitlinie F-16 |
15.03.2016 | Do the essential safety requirements apply to temporary components used by the equipment manufacturer either during the manufacturing or for the proof test of a pressure equipment? | ||||||||||||
Leitlinie F-17 |
15.03.2016 | Is the manufacturer allowed to replace non permanent joining components (bolts, studs, nuts, washers, gaskets) at the end of the proof test without carrying out a new proof test? | ||||||||||||
Leitlinie F-19 |
21.03.2017 | The Essential Safety Requirements define in Annex I chapter 3.1.2 that the properties of welded joints shall meet the minimum properties specified for the materials to be joined unless other relevant property values are specifically taken into account by the design process. Do these requirements apply also for impact property values? |